Dake Model E-V Series Manual do Utilizador

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 1 – Section I JOHNSON VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST SECTION I – Manual

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 10 – Section I BLADE TENSIONING The blade indicator is located inside the upper wheel compartm

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 11 – Section I An analysis of the work to be performed should be made and the proper blade sel

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 12 – Section I HIGH SPEED ROLLER GUIDES Applications and Advantages: Friction and abrasive cutt

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 13 – Section I 4: Insert the mounting stud (B) into the guide casting (A). Keep the stud flus

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 14 – Section I Repeat this process for the lower guide assembly. Note: Upper guide stud may be

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 15 – Section I Note: Occasionally the drive wheel may have to be jogged by hand to engage the

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 16 – Section I SAW BLADE SELECTION MATERIAL SHAPE MATERIAL SHAPE MATERIAL SHAPE MATERIAL IN

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 17 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" 1100,

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 18 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" A-6

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 19 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7"

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 2 – Section I If machine is to be operated At 440 volt 3 phase power, please read the following

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 20 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" INCON

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 21 – Section I HYDRAULIC FEED TABLE Machines equipped with a hydraulic feed table (VH models)

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 22 – Section I This welder should not be used for welding 2% and 3% tungsten-alloyed metal cutti

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 23 – Section I Turn the upsetting switch (3 figure 1) past the position (5 figure 1) to welding

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 24 – Section I 8. POOR WELDS / TROUBLE SHOOTING If the welded seam contains holes, the upsettin

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 25 – Section I USE OF STANDARD AND OPTIONAL ACCESSORIES CIRCLE CUTTING (OPTIONAL) (figure 1) (

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 26 – Section I T-SLOTS T-slots are machined into the work table for your use with fixturing or

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 3 – Section I SECTION I - TABLE OF CONTENTS Specifications ...

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 4 – Section I SPECIFICATIONS Model Number: V-16 V-24/VH-24 V-40/VH-40 Capacity:

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 5 – Section I

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 6 – Section I

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 7 – Section I MACHINE UNPACKING AND INSTALLATION UNLOADING: Remove the shr

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 8 – Section I FILLING THE SPEED REGULATOR This is pre filled at the factory These instructions a

7/21/08 Manual V-16, V-24, VH-24, V-40 & VH-40 9 – Section I WHEEL ALIGNMENT V-16 & V / VH-24 Note: This alignment is factory set, but may